356 - 912 Push rod, street and racing
ELE 105 028 02
We are pleased to offer new pushrods in highest Swiss quality. Also suitable
for race engine for high RPM. Much stronger aircraft alloy material (AA2124 T851)
much lighter to have minimum reciprocating mass, slim to make sure they don't
touch the oil return tubes. (Some early B pushrods had this problem)
The standard length is 256,7 mm (10.106"), we offer a short version with 255.7 mm
(10.067") for engines that the heads were resurfaced.
Standard length fits ALL 356 engines, cast or alloy cylinders !
Many old push rods are slightly bent and the oil holes are plugged. For every serious
full engine rebuild, the push rods should be replaced.
Made in Switzerland by JPS, exclusively sold by us.
356 - 912 Racing and street deep sump
616 101 039 99
NEW !! Made in high precision and perfect SWISS quality.
Small deep sump for 356 - 912 engines, 0.3L more oil, prevents oil
starvation in long corners, better cooling, strong ring magnetic filter installed.
Easy to install, all hardware included. For street and track use.
Made in Switzerland by JPS, exclusively sold by us.
If the 356 has new transmission rubber mounts installed, the deep sump
will have more ground clearance then the lowest point, which is the transmission
hoop. Ground clearance on 912 is no problem.
HELLA headlamp glas Seal beam - clear
644 631 111 31
For seal beam and for new LED light. clear HELLA lense. Also used on very early 911
RECARO seat hinge covers
644 521 915 00 - 916 00
Excellent quality and fit
356 C Grey
Driver 644 521 915 00 Pass. 644 621 916 00
911-912, 1965 - 1967, Grey
Driver 901 521 915 00 Pass. 901 521 916 00
911-912, 1968, Black
Driver 901 521 915 00 Pass. 901 521 916 00
NOTE - same part number - indicate Grey or Black !!
911-912, 1969 - 1973, Black
Driver 901 521 915 01 Pass. 901 521 916 01
911-912, 1974 - 1976, Black
Driver 911 521 915 01 Pass. 911 521 916 01
Door hinge pin kit
ELE 531 305 99
New door hinge pin kit all 356
Dash board chrome handle 356A to 356 B T6
ELE 552 865 00
Very nice reproduction of the chrome grab handle. Made in Italy. Includes hardware. Made in brass casting with deep chrome and correct edge.
356 Cabriolet polished aluminium nail strip
ELE 561 881 00
Excellent reproduction of the Cabriolet nail strip at
the rear top bow.
356 B T6 - C, Fresh air channels
New reproduction - Made in Italy
ELE 572 693 06 - Rubber T-piece left
ELE 572 694 06 - Rubber T-piece right
ELE 572 691 06 - Rubber sleeve left
ELE 572 692 06 - Rubber sleeve right
Sold in pairs only !! Good high quality soft rubber, finish acceptable.
ELE 571 012 06 - Air collection funnel
Steel wheels 16* x 3.25
356 68 021
Finally we have received the first small production (200) of
our new 16* steel wheels. Made in Italy.
We apologize for the delay, but some important improvements
had to be incorporated on request by the TUV authorities.
The final product is very good and very nice. You and your
customers will be pleased. We road tested 2 sets.
The date circle was left blank, your customer can, if he likes,
add month and year. The rims are painted in a high quality
primer paint as a good base for final paint in silver or car color.
We tested to chrome 4 rims with satisfactory result but the cost
was close to Euro 300.00 each! Therefore we do not offer the
Ref. part. Nr. 356 68 021
Size 3.25D x 16
TUV Nr. 874 0721
Single rim box 45x47x12.5 cm, 6.8 kg with box.
Included is copy of TUV in German, Italian and English plus design drawing.
Chromed rims on special request available
356 A - C rear seat bolt kit
ELE 021 121 00
Bolt kit for the rear seats for all 356. Special 8mm bolt with rubber washer and wavy washers.
356 12 bolt differential carrier
741 332 101 01
Made in Germany, good reproduction of the reinforced 12 bolt differential housing
356 A steering column bracket
644 47 026 2
644 47 026 Steering column support - bracket
Speedster - Convertible D
644 47 026 2 Steering column support - bracket
356 Coupe - Cabrolet
644 47 213 Steering column rubber support
Speedster - Converible D
644 47 213 1 Steering column rubber suppoert
356 Coupe - Cabriolet
644 347 755 05 repl. number
356 A Horn ring NEW production
ELE 347 811 01
Very nice and authetice A horn ring. Excellent quality Made in Italy.
Rubber seal for horn ring ELE 347 811 09
Pre A interior lights NOS Hella
644 632 101 01
Interior lights for the pre A. Limited inventory, old stock. (old part. nr. 356 61 060)
SOLEX velocity stacks
ELE 108 203 20
Very nice new production for the SOLEX 40 carburetors. With special screws.
Windshield wiper switch 4 connector / Single switch
ELE 613 501 00
Excellent reproduction of the original 4 connector 356 wiper switch with correct bullet connectors. For all 356A to B T5.
Small single switch for fuel pumps, fog light etc. with 2 screw connectors.
Correct beige and black knob with correct bezel.
The 4 conn. switch is also available in reverse function for the 4-cam CARRERA car. Push in - ON / Pull out - OFF
Bullet connectors for authentic installation.
Speedster dashboard chrome trim Original GHE
Original OLD stock of Happich GHE chrome trim for the Speedster dash. 4.5 mm diameter, very soft material. Only a few meters
HELLA headlight spare parts
new available spare parts for the HELLA headlights
- 644 631 111 02 spare glass
- 644 631 114 00 spare rubber gasket
- 644 631 117 02 spare reflector
HELLA headlight for Lefthand traffic
644 631 101 00
New Old Stock - HELLA original headlights for Lefthand traffic - UK, SA, J etc. limited quantities.
356 Cabriolet top frame B-C
Excellent reproduction of the Cabrio top frame for all B to C cars. With some minor changes it should also fit the 356 A T2 cars. Correct tubings, latches, castings and rear wooden bow. The front wood bow is easy available. We have sold over 30 without any complains.
Script - 1500 - gold
540 58 301
First used only on the Speedster then also on the other 1500 356 cars.
NEW Durant outside mirror
NEW reproduction of the MALL Durant outside mirror.
Excellent quality with correct adjusting angle, perfect shape and correct base gasket.
Comes with flat glass or convex glass.
Fits all 356 C models from 1964 up to 911, 912 up to model 1968.
Tecnomagnesio 356 wheels 5.0 x 15 tubeless
Final and limited production !
Outstanding production of the magnesium wheels. Made in Italy. Size 5.0 x 15, tubeless, fits tires 165x15 - ideal is 175/70x15 or larger. Only 5.5 kg (Mangels chrome steel 7.7kg) The wheels have TUV certification and are legal for road use in Europe. Included are 5 special wheel bolts.
Hubcap fitting not possible.
356 windshield wiper gear SWF
New windshield wiper gear Type SWF for all 356 from Mod. 54 up to B T5 1961. Most of the gears are worn out and noisy. Replaces BOSCH and SWF gears.
644 628 025 00 or BOSCH 644 628 025 10
Reflectors K1315 356 1952 up to 1959
After many failed attempts and disappointing samples from Germany and China we found a excellent producer in Italy that got it done right !!
The reflectors have been missing for 30 years and most A cars have the later ULO installed. Old original glass reflectors sell on ebay for US$ 500.00 and more per piece !!
The shape and looks of our reproduction is perfect. The material used is called +artificial glass+ it looks, feels, weighs and performs just like the old glass. This material was developed too comply with new environment laws and for safety reasons for other applications. The brushed housing and the chrome ring is excellent. We choose the small K1315 lettering, originally there were 2 versions of small and larger lettering.
ELE 731 501 00 R?ckstrahler - Reflector K1315
Set of 2 pcs.
Made in Italy
Ignition switch and door locks
after 2 years development we can proudly offer excellent ignition switch and door locks. They are the late C version (K300) but also fit the early cars. Many ignition switches do not work correctly because of worn out contacts and weak springs. Many 356 have 3 different keys, one for each door and the third one for the ignition. Finally we can offer a attractive solution
ELE 613 101 06 Ignition lock with 2 keys
ELE 613 901 00 Door lock left - right, 2 keys
ELE 613 101 99 Ignition-Door lock kit, 4 keys
1- ELE 613 901 10 Key blank 300
2- ELE 613 191 03 Ign. switch bezel
3- ELE 613 505 00 Light switch bezel
4- ELE 613 101 20 Ign. lock nut
5- ELE 613 101 21 Ign. lock nut washer
6- ELE 531 606 01 Rubber washer receiver
7- ELE 531 607 01 Nylon collar door lock
Your 356 parts retail dealer should have them in stock soon.
356 front sway bar 17.5 mm
Fits all 356 models. Cold formed from chrome moly steel and hardened to 48 Rockwell just like the original bar, and then powder coated in satin black. Correct with tapered ends, and correct (but larger) clamps, for an authentic appearance. Complete with 20% harder rubber bushings for a positive feel without the problems associated with poly bushings (upper drop link bushings are two piece with a stainless sleeve to ease installation). Designed to improve street handling performance, and high speed stability, without compromising ride quality and originality.
The increase in stiffness is 85% for the 356A/B (originally equipped with a 15mm bar) and 42% for the 356C (originally equipped with a 16mm bar). Most aftermarket swaybars are not hardened. This reduces the cost but makes it necessary to use a larger bar to achieve the same rate. The W/R 17.5mm Sport Swaybar is hardened to 48 Rockwell just like the oem bar.
The first 356s had no front swaybar. In order to reduce the oversteering characteristics of the car, Porsche began using a front swaybar in late 1955. This bar was 15mm in diameter, and continued until late 1963. With the 356C the bar was increased to 16mm. To further reduce oversteer (and wandering), especially at high speeds, we experimented with bars up to 19mm. We found the 17.5mm bar to be the perfect size. It reduces oversteer to a minimum, flattens the car in cornering, but doesn't dramatically change the characteristics of the 356.
This bar is a must for all 356s, especially with wider wheels and tires!
Ring and pinion 7:31 NEW
NEW production of the highest OEM quality by HOER - Klingenberg ring and pinion. Standard size of 7:31
There are all sorts of qualities in the market, make sure you buy the OEM quality.
NEW, early 356 interior mirror - 1952 to 1961
Outstanding, perfect reproduction of the early 356 interior rear view mirror. For 356 from 1952 pre A up to B T5, Coupe and Cabrio, Speedster, Convertible D and Roadster. Also available both fully correct holding clamps.
Mirror size 175 x 60 mm, very nice satin dull finish to prevent reflections, fully correct mounting arms, excellent mirror glass mounted flawlessly.
When we started this project over one year ago, we noticed in the Porsche spare parts books that the same part number was used for all 3 different style mirrors, also the 2 very different holding clamps used the same part number !!
Original early part number for the mirror was 356 70 033 replaced by 644 731 101 01 for all 3 mirrors and for both clamps, early number 357 70 303 replaced by 644 731 150 21.
ELE 731 101 01 - mirror with early 2 hole mount,
ELE 731 101 02 - mirror with late, 1956 to 1961, 1 hole mount
ELE 731 101 40 - mirror with round arm Speedster, Conv. D, Roadster, Cab
ELE 731 150 21 - early double clamp
ELE 731 150 25 - late single clamp.
Dash knobs for 356
New high quality reproduction (Switzerland) of the black and beige knobs. Perfect look, perfect feel, perfect shape.
356 Speedster windshield frame
Excellent reproduction of the Speedster windshield frame, top bow, 2 side posts and lower lip. All made in high quality brass. Each set must be adjusted to your car, then you can drill holes to the top bow and have the parts chromed. We have noticed that each original Speedster windshield frame is a little different and was individually adjusted to each car.
Transmission bearing 741 - 915
644 20 207 transmission bearing, also used as 915 302 399 05 for the 915 gear box. d30 D62 B20
NOS fuel filter for early engine
539 108 909 08 original fuel filter for early engines
Porsche 356 A to B and all Cabriolet Interior light
Very nice reproduction of the interior light.
Solex 40 Race air intakes
ELE 108 203 11
Nice new reproduction for the racer 356 with Solex 40. Available in silver and red. 60 mm high. Improves overall performance.
New production: Clamp nut for front axel - Klemmutter
Front axel clamp for Porsche 356 from 1956 to 911 and 912 up to 1989 and all 914. Soon not available from Porsche. Ref.Nr. 644 341 671 00 or 914 341 671 00.
Porsche 356 A Shin up license lights
Excellent reproduction of the Hella Shin up light. Used on all 356 A from Chassis Nr. Coupe 100 001, from Cabrio 61701, from Speedster 83201 and up. (1957-59)
NEW Oel - Oil cap for 356
New perfect reproduction of the long time missing oil cap for the Porsche 356 late B, C and SC, Carrera, 912 and very early 911.
Porsche 356 generator pulley half
Excellent new reproduction, Made in Italy, of the generator pulley half. outer Ref. Nr. 539.09.315, inner with notch Ref. Nr. 539.09.316. Perfect fit on shaft and correct white zinc plated.
New Big bore kits with alloy "Biral" cylinder, 86 mm 1720 ccm
NLA 103 901 96 - 98
New Big bore generation, with alloy cast cylinder, much lighter (1.56 kg versus 2.14 kg !!) much better heat dissipation, ensuring strength and thermal control. Available with high grate forged JE piston or for normal use with cast pistons.
NLA 731 002 00
Excellent new reproduction of the famous AERO mirror used on Porsche 356 A includes pre-A Speedster and Convertible D. 1955 to 1960. Outstanding chrome, sharp production stamp and perfect edge (not like the cheap early reproductions). Additional we made the mirror with Convex glass, also available separate, increases the rear view vision angle by 50%. Good for your safety !!
NEW - MESSKO tire gauge
Perfect new reproduction of the MESSKO tire gauge with chrome housing used in all 356 tool kits up to 1963. Black or red leather pouch with 100% correct Quality tag. Excellent product.
NEW, Porsche 356 B - C de luxe horn ring
Excellent reproduction of the optional de luxe horn ring. Also used on all VDM wood steering wheels.
Transmission Rebuild Kit 716 and 741
NLA 300 003 00
Excellent complete transmission rebuild kit with all paper gaskets, 4 synchro rings, 4 roller bearing (hard to find) seals, washers, splints, clip rings etc.
NEW - Air-cleaner for Zenith and Solex
616 08 108
New KNECHT SPORT air cleaner for all Zenith 32 and Solex 40. Ref. Part. Nr. 616 08 108 (Zenith) 527 08 801 (Solex) Hight 80 mm, Diameter 130 mm, Intake diameter 66 mm. Special fine dust filter permanently inside. The filter can be washed with cleaning solvent.
New improved version with velocity stack for better performance.
356 Interior mirrors for B T6 and C and early 911 - 912
New excellent exclusive reproduction of the "day-night" interior mirror.
644 731 101 06 day-night, Break-a-way mount
644 731 101 07 day-night, 3 screw mount,
644 731 101 26 day-night, C Cabriolet,
901 731 010 20 Int, mirror, day-night, Porsche 911 - 912, - 1968
356 Super 90 - SC - 912 Sport Airfilter
New and improved reproduction of the KNECHT air filters for all Solex 40 carburetors. Used on Super 90 - SC - 912. Fixed filter element, it can be cleaned with cleaning solvent. 35 mm velocity stacks inside. Original filter do not have any stacks. Includes screws and washer. Cover and bottom plate and wire mesh in alloy.
Power increase 2-4 HP, tested by John Willhoit.
Dashboard "Meisterschaften" badge, 1956
NLA 559 831 02
Very nice reproduction of the "1950-1956 Deutsche Sportwagen Meisterschaften" dashboard badge.
REUTTER badge for A and B, C cars
NLA 723 004 00
REUTTER badge for
NLA 723 003 00 356 A "Germany"
NLA 723 003 01 356 A "3 diamond" European cars
NLA 723 004 00 356 B - C
excellent reproduction with correct gold rivets
356 Talbot outside mirror 1958 to 1962
NLA 731 003 06
Very nice and exact reproduction of the correct TALBOT outside mirror used from 1958 to 1962 on all 356. Correct light grey rubber base gasket.
Can be used left and right. Pictures of a 100% original paint and never touched T5 Roadster.
LED Brake and blinker light bulb NEW Design
New design LED brake and blinker bulb for vertical and horizontal use. Single and double connectors, 6 and 12 V.
12 V Starter Motor 1.3 HP
Hi - Horse 12 V starter motor. 1.3 HP, 1:4.4 gear ratio, only 4 kg, 5 full roller bearing construction, front plate can be rotated for perfect fit, fits any 356 with 12V.
356 Luggage rack NEW, Lietz chrome and Reutter paint
Excellent reproduction of the original luggage racks. Stainless steel (looks like chrome) rack from LIETZ with mounting hardware. Red ski straps on demand. Painted Reutter rack with hardware. Both racks fit all 356 model, single and twin grill.
Tubular LED lamp - Soffittenlampen LED
New product. 6 and 12 V, 42 and 36 mm tubular LED lights.
MARCHAL Fog and Long Range Rally lights
Excellent exclusive reproduction of the world famous MARCHAL lights from the late 50's and 60's. Used OE on the Ferrari 250 and used by countless Rally drivers.
Type 670 Fog - Type 672 Long Range, in 6 V and 12 V, with Tungsten bulbs or H3, with clear or yellow bulbs.
Set includes 2 lights of your choice, 1 relay, 1 cable connector
Long range SOLD OUT.
Porsche 356 A B brake cylinder
695 351 511 00 upper right lower left - front
695 351 512 00 upper left lower right - front
695 351 513 01 rear
New reproduction, excellent qualtity, good price
Alloy wheel spacers for 356 drum brakes
- 1/8" , 3mm, 160 gr.
- 1/4" , 6.5 mm, 350 gr.
- 1/2" , 13 mm, 680 gr.
- 3/4" , 19 mm, 1060 gr.
356 and 911 LED instrument lights 6 and 12V
Very nice and bright LED instrument lights. Finally you see the dials at night and the important control lights in the day light. LED lights do not generate heat, therefore your instruments stay cool (no condense humidity inside the instruments !!) See pictures with regular 0,6 and 1.2 W lights and after with LED !! LED is 20X brighter then a regular 0,6W light bulb !!
Single and dual connectors.
356 Pre A idiot lights - Back in stock
NLA 61 070
Outstanding reproduction of the original 356 idiot lights, green, red and blue. Also used on later 356 for fog light and heated windscreen control lights.
Hub cap 356 A and B
Outstanding reproduction of Super hub cap for 356 A and all B. Weight 600 gr - 21 ounce. Check the weight of the cheap repro's that you can buy........
Porsche 356 A silver data plate original
Original 356 data plate, NewOldStock, limited quantity.